Programing Data ( EPROM,EEPROM,FLASH,PIC )
1. Select device type (Menu Device)
2. Set the DIP switch (see window STATUS).DIPswitch
switches can be red(like in the sofware),white or other colors.
3. Load program file (Menu File -> Load xxx)
4. Insert the IC to the ZIF Socket or the DIP socket
5. For:
Eprom 27Cxxx,27xxx make sure you earase all data (UV erase) by use (Menu Action
-> Checkempty)
Flash,Eeprom erase data by (Menu Action -> Erase 28x, 29x, 49x,
AT89x)
PIC check parameter setting first by use (Menu Progsettings)
6. Program (Menu Action -> Program)
Reading Data ( EPROM,EEPROM,FLASH,PIC )
1. Select device type (Menu Device)
2. Set the DIP switch (see window STATUS)
3. Insert the IC to the ZIF Socket or the DIP socket
4. Read data (Menu Action -> Read)
5. Save data, You can save as two types 1. binary(.bin)
or 2. Intel hex (.hex) (Menu File ->Save xxx)
Programming MCS-51 (Adapter board is needed
1. Select pin type (40 or 20pin) and number program (Menu
Device)
2. Set the DIP switch (see window STATUS).
3. Insert the IC to Adaptor board
4. Select device type. For ATMEL chip you can read the ID code
and set parameters automatically (auto select)
5. Load program file (Menu File -> Load xxx)
6. Erase old program existing in the IC (Menu Action ->
Erase 28C,29C,AT89)
7. Burn program (Menu Action -> Program)
8. Protect your data ( protect from copying ) (Menu Action
->Lock Bit)
TIPS
Programming AT89C55WD is needed voltage at least 5.6V
Programming data into the IC (follow ATMEL specification, it
guarantees at 6.5 V)
If voltage less than 5.6V, it maybe can't program some lot of
CHIPs.
It can solve this promblem by attaching one diode at the
second pin of the IC 7805.
The voltage that supply to the IC will be 0.6+0.6+5 = 6.2 V
and the voltage that supply other chips will be increase 5.6
V.
When you have finished programming, you should move the added
diod out to decrease voltage to 5.6V. |
| EPROM |
27C64, 27C128, 27C256,
27C512, 27C010, 27C020, 27C040,27C1001
M27C1001, M27C2001, M27C4001
27C080 (A19) ,M27C801,M87C257
2716(Vpp25V),2732, (adapter DIP24)
2764, 27128, 27256, 27512, 27010,
Vpp12.5V (21Vpp Modify Circuit) |
| EEPROM |
28C65,28C64, 28C128,
28C256,28C512, 28C010, 28C020, 28C040
M28C16A/17A (DIP28)
(Adapter or Jumper) 28C16,XLS2816 (DIP24) |
| FLASH Memory |
28F64, 28F128, 28F256,
28F512,28F010, 28F020
MX26C1000, MX26C2000, MX28F1000, MX28F2000
Am28F256A, Am28F512A, Am28F010A, Am28F020A (New command erase/prog.)
-- intel ---
i28F001BX, 28F004, 28F008, 28F016 |
| FLASH Memory |
29F64, 29F128, 29F256, 29F512,29F010, 29F020, 29F040,
29F080
29F001,29F002, 29F004, 29F008, 29F016, 29F032 |
Serial (I2C) EEPROM
24Cxx |
24C02,24C04,24C08,24C16,
85C72, 85C82, 85C92
--- page write ----
24C32,24C64,24C128,24C256,24C512 |
Microwire EEPROM
|
<------
Data 8bit -----> (pin 6 ->ORG. [Schematic connect to GND])
93C06, 93C46, 93LC46, 93C56, 93C57,
93C66, 93C76, 93C86 (8bit), AT59C11, AT59C22, AT59C13
CAT35C102, CAT35C104, CAT35C108 (pullup pin7)
<------Data 16bit------> (pin 6 ->NC [No Connect])
93C06A ,93C46X,93C56,93C66,93C76,93C86 (NS) |
| MicroChip PIC |
16C84, 16F84, 16F84A
,16F627/16F628
12C508/A, 12C509/A, 12CE518, 12CE519, 16C505
16C620 16C621, 16C622, 16CE623, 16CE624, 16CE625, 16C710/711
PIC 16F818/819
---ICSP connector----
16F870, 16F871, 16F872, 16F873, 16F874, 16F876, 16F877
PIC16F873A, PIC16F874A, PIC16F876A, PIC16F877A |
Atmel Flash Memory
(Sector Programming)
(Software Data Protection) |
AT29C256,
AT29C512,AT29C010A, AT29C020, AT29C040,AT29C040A
W29EE512,W29EE011, W29EE012, W29C020(128),W29C040
PH29EE010(W29EE011) ASD AE29F1008 ,
AE29F2008
Ver 0.992 up(DOS). Can run under win9x
(disable prog. CPUIdle or CPUCool) |
Atmel Flash Memory
AT49Fxxx (Subset 29Fxxx)
(Byte-by-Byte Programming)
(Software Data Protection) |
Command seq. 5555/AA,
2AAA/55, 5555/A0
AT49F512, AT49F010, AT49F020, AT49F040
SST39SF010, SST3S9F020 ,SST39SF040
AT49F001,AT49F002 , AT49F008A
Command seq. 555/AA, 2AA/55, 555/A0
Am29F512, Am29F010, Am29F020, Am29F040,HY29F080
29F002, 29F002T, Pm29F002T |
Serial Peripheral Interface
(SPI)
EEPROM Mode0 (0,0)
AT25xxx, W95xxx |
[Atmel] AT25010,020, 040
(A8-A0)
AT25080, 160, 320, 640, 128, 256 (A15-A0)
[ST] W95010....256, Microchip 25x010 - 25x640 --- Byte
programming
25010,25020,25040
--- Page programming
25C080,25C160,25C320,25C640,25C128,25C256,25C512
AT25HP256,AT25HP512
AT25HP1024 (24bit address)
-- CAT64LCxxx (16bit DATA IN/OUT) use Socket 93Cxxx
CAT64LC010, CAT64LC020, CAT64LC040 |
Atmel EEPROM (page prog.)
(Software Data Protection) |
AT28C256,
AT28C010, AT28C040 |
| Nonvaltile SRAM (DS12xx) |
DS1220,DS1225Y, DS1230Y/AB,
DS1245Y/AB, DS1249Y/AB |
| static RAM (Test RAM) |
6116, 6264, 62256, 62512,
628128 |
EPROM winbond,SST
Electrical Erase Chip |
W27E512, W27E010, W27C010,
W27C020, W27C040
SST27SF256, SST27SF512, SST27SF010, SST27SF020
MX26C4000
Vcc = 3.3-3.6V SST37VF512, SST37VF010, SST37VF020, SST37VF040 |
| Flash Memory SST,Sanyo |
SST28SF040A ,LE28F4001 |
|
Adapter |
Atmel AT89Cxx (MCS-51)
Adapter 32pin to MCS-51 |
Atmel
Auto Setect
AT89C51,52,55, AT89LV51,52,55
AT89S8252 (8K+2K), AT89S53, AT89LS8252,AT89LS53
AT89C1051,AT89C2051,AT89C4051 (20pin)
AT89C51RC (32KB), AT89C55WD (6.2V)
AT89S51, AT89S52
SST89C54/58, SI89C52
Intel Auto Select
i87C51, i87C51FA, i87C51FB
------------------------------------------------
i8xC51,i8xC52,i8xC54,i8xC58 (tWP = 100uS*25 Pulse) |
Atmel AVR 8-bit RISC AT90Sxxx
(Parallel programming)
Adapter 32pin to MCS-51 |
(read,write,erase,verify,checkempty,Lockbits
,Fusebits) [Flash memory/EEPROM]
AT90S1200,AT90S2313
90S2333, 90S4433, 90S4414, 90S8515,
90S4434, 90S8535
reference AT90S2313 pin
Function Lockbit read AT90S2313 Errata
Sheet.pdf |
MCS-48,MCS-41
Adapter 32pin to MCS-48/41 |
ROM
(read/verify)
P8048AH, P8049AH,P8050AH, P8042AH Vea = 12V
P8041, P8042
OTP (read/verify/Progam)
P8748,P8749H,P8742H Vea = 18V
EPROM (read/verify/Progam)
D8748,D8749,D8742,D8741, D8742 Vea = 18V
|
FLASH memory 8/16bit
(Software Data Protection)
Adapter (TSOP48) |
Am29F400,Am29F800,29F160,29F320
(read,write byte mode)
HY29F200, HY29F400, HY29F800 , AT49F2048A, AT49F4096A, AT49F8192A |
FLASH memory 8/16bit (Vpp12V)
(Software Data Protection)
Adapter (TSOP48) |
i28F200,i28F400,i28F800,i28F160
(TSOP48)
28F001(DIP32 or PLCC32)
|
EPROM 16bit (DIP40) (1-4Mbit)
Adapter Eprom 16bit
Eprom only
|
27C1024 (27C210), 27C2048
(27C2002), 27C4096 (27C4002),
Schematic by Toomas Toots
(read,Program byte mode
by use Resister pull up Data Bus (0xFF), A0 select low or high byte)
|
EPROM 16bit (DIP42)
(4-32Mbit)
Adapter Eprom DIP42
Eprom only
|
M27C400(DIP40), 27C800,
27C160, 27C322
Schematic by Toomas Toots
(read,Program byte mode
by use Resister pull up Data Bus (0xFF), A0 select low or high byte)
|
FLASH memory 8/16bit
(Software Data Protection)
Adapter (TSOP48LV) |
29LV200,
29LV400,29LV800,29LV160,29LV320 (read,write byte mode)
|
Firmware Hub / LPC FLASH
Adapter Firmware Hub/LPC (PLCC32) (PP
mode) (3.3V)
|
-- Firmware Hub
82802AB, 82802AC, AT49LW040, AT49LW080
SST49LF002A, SST49LF003A, SST49LF004A, SST49LF008A
W49V002FA, W39V040FA -- LPC flash
SST49LF020, SST49LF040
W49V002A, W39V040A |
P28F002BC
Adapter P28F002BC (DIP40)
|
BOOT BLOCK FLASH MEMORY
- P28F002BC
|
PIC:
|
